How to Calculate Concrete
Multiply the length, width and depth in metres to get cubic metres of concrete: a shed base 2.4 m (7 ft 10 1/2 in) by 1.8 m (5 ft 10 7/8 in) and 0.1 m (3 15/16 in) deep is 0.43 m³ (15.26 ft³), which is 44 bags of the bagged mix used in the table below.
Estimates for planning, not professional advice. Read the full notice.
Work it out for your own sizes
See the working for a base of this sizeExample to try: Length 2.4 m (7 ft 10 1/2 in), Width 1.8 m (5 ft 10 7/8 in), Depth 0.1 m (3 15/16 in)
Step by step
-
Step 1: Measure in metres
Measure the length and width of the base with a tape and write the depth in metres too, not millimetres: a sum that mixes the two gives an answer far too big or too small. The shed base in the table below is 2.4 m (7 ft 10 1/2 in) long, 1.8 m (5 ft 10 7/8 in) wide and 0.1 m (3 15/16 in) deep.
-
Step 2: Multiply length, width and depth
Length times width times depth is the volume of the base: 2.4 m (7 ft 10 1/2 in) × 1.8 m (5 ft 10 7/8 in) × 0.1 m (3 15/16 in) is 0.43 m³ (15.26 ft³). A path and a drive are worked the same way in the table.
-
Step 3: Add a waste allowance once
Ground is rarely perfectly level and some mix stays in the barrow, so a waste allowance goes on the total volume, once, never on each measurement. The worked example on the concrete calculator page shows the allowance as a setting. The table on this page leaves it off so the sum stays visible.
-
Step 4: Turn cubic metres into bags
Divide the volume by what one bag makes and round up once to whole bags. One 20 kg (44.09 lb) bag of Blue Circle Multi-Purpose Concrete makes 0.01 m³ (0.35 ft³, converted)[1] by the maker's sheet, so the shed base needs 44 bags before any waste allowance.
One 20kg bag will typically produce around 0.01 m3 of fresh concrete (0.33m x 0.33m x 0.1m).
Three bases worked through
Cubic metres of concrete and bags for a shed base, a path and a drive, before any waste allowance
| Base and size | Cubic metres | In 20 kg bags |
|---|---|---|
| Shed base, 2.4 m × 1.8 m × 100 mm | 0.43 m³ (15.26 ft³) | 44 × 20 kg (44.1 lb) bags |
| Path, 5 m × 1 m × 75 mm | 0.38 m³ (13.24 ft³) | 38 × 20 kg (44.1 lb) bags |
| Drive, 6 m × 3 m × 150 mm | 2.7 m³ (95.35 ft³) | 270 × 20 kg (44.1 lb) bags |
Estimate for planning, from what you entered and the product data shown. Check product labels and your supplier before you buy.
Each row is length times width times depth. The bags are rounded up once, with no waste allowance, for the one bag size named in the last column. Product names are trademarks of their owners. HoneyDoMath is not affiliated with, sponsored by or endorsed by these makers. Figures come from each maker's published sheets and are shown for information only.
If you are ordering ready mix
The cubic metres column is the figure a ready-mix order is placed in, so it carries straight over. The ready mix calculator page works the same sum for an order.
Questions
How do I calculate the volume of concrete?
Multiply the length, width and depth, all in metres, to get cubic metres. The table on this page does it for a shed base, a path and a drive.
How many cubic metres of concrete do I need?
It depends on the size of the base. The table gives the cubic metres for three bases, and the same sum works for any rectangle.
Why do the bags come out as whole numbers?
Bags are bought whole, so the count is rounded up once at the end of the sum, never on the way.
Calculate it for your project
Enter your own sizes to get the amount to buy or the layout figures, with the maths shown and a page to print.
Concrete CalculatorSources (1)
-
Multi-Purpose Concrete Product Data Sheet (opens in new tab), Tarmac Trading Limited (Blue Circle), December 2023.
Manufacturer data.
“One 20kg bag will typically produce around 0.01 m3 of fresh concrete (0.33m x 0.33m x 0.1m).”
Per Blue Circle's data sheet, checked 12 Nov 2026. Figures and regulations change; verify with the source. Back to where this is used (Source 1)
These are summaries of what the sources say, not professional advice. Rules and product data change. Check with your local building control office and the product label about your own project.