Plasterboard Calculator

Enter a room's length, width and wall height to get the plasterboard sheets for walls, ceiling or both, then the jointing compound, tape and screws for the same board, rounded up once for each item you buy. The sheets are the larger of the area count and the cut-layout count, and both are shown.

Estimates for planning, not professional advice. Read the full notice.

Room and finishing

Metres, centimetres or millimetres, like 3.8 m, 10 cm or 250 mm

reads as 4.2 metres, 13 feet 9 and 3 eighths inches

Metres, centimetres or millimetres, like 3.8 m, 10 cm or 250 mm

reads as 3.6 metres, 11 feet 9 and 3 quarters inches

Metres, centimetres or millimetres, like 3.8 m, 10 cm or 250 mm

reads as 2.5 metres, 8 feet 2 and 7 sixteenths inches

Like 11 m²

reads as 4.5 square metres, 48.44 square feet

Like 40 L

reads as 40 litres, 10.57 gallons

Metres, centimetres or millimetres, like 3.8 m, 10 cm or 250 mm

reads as 120 metres, 393 feet 8 and 7 sixteenths inches

Like 11 m²

reads as 0.08 square metres, 0.86 square feet

Example: a bedroom, walls and ceiling

31 sheets of plasterboard

  • Walls and ceiling together 54.12 m² (582.54 ft²)
  • Sheets by area, with the waste, before rounding 20.67 sheets of plasterboard
  • Sheets by area, rounded up 21 sheets of plasterboard
  • Sheets by layout, cutting each wall and the ceiling 31 sheets of plasterboard
  • Sheets by area with the openings taken off 19 sheets of plasterboard

Estimate for planning, from what you entered and the product data shown. Check product labels and your supplier before you buy.

  • Plasterboard sheets, 2400 × 1200 mm 31
  • Jointing compound tubs, 10 L tub 3
  • Joint tape rolls, 50 m (164 ft 1/2 in) roll 2
  • Plasterboard screws 677

Share this project

This link carries:

    The project is inside the link, after the # sign. Browsers do not send that part to the site.

    Questions

    How many sheets do I need for the walls and the ceiling?

    Enter the room's length, width and wall height and choose Walls and ceiling. The calculator adds the four walls and the ceiling, adds your waste allowance once, divides by the area of one sheet and rounds up once, then counts the cut layout and uses the larger of the two counts. Choose Walls or Ceiling to count one surface alone.

    Does a longer sheet change the count?

    Yes, a longer sheet covers more area, so the count usually falls. Change the sheet size above and the sheets, and the finishing that follows the board area, update together. The sizes in the list are example values, so choose the one your supplier sells.

    Do the doors and windows come off the count?

    The calculator starts with the walls counted gross, with openings not taken off, and shows the count with the openings taken off beside it. Enter the area of your openings and switch Openings to Taken off to leave them out.

    Where do the compound, tape and screw amounts come from?

    From three rates in the fields above, each started at an example, not a maker's figure. Replace them with the rates on your own labels and the tubs, rolls and screws follow the board area.

    Worked example: a bedroom, walls and ceiling

    Show the working
    1. Walls: the perimeter times the wall height 15.6 m (51 ft 2 3/16 in) × 2.5 m (8 ft 2 7/16 in) = 39 m² (419.79 ft²)
    2. Ceiling: length times width 4.2 m (13 ft 9 3/8 in) × 3.6 m (11 ft 9 3/4 in) = 15.12 m² (162.75 ft²)
    3. Add the waste allowance, once 54.12 m² (582.54 ft²) + 10% = 59.53 m² (640.8 ft²)
    4. Divide by the area of one sheet 59.53 m² (640.8 ft²) ÷ 2.88 m² (31 ft²) = 20.67 sheets of plasterboard
    5. Round up once, to whole sheets 20.67 sheets of plasterboard = 21 sheets of plasterboard
    6. Count the layout too and use the larger of the two, so a cut layout is never short 31 sheets of plasterboard = 31 sheets of plasterboard

    Assumptions

    The figures behind the example. Sourced figures link to their source below; a default is a starting value to check against your label or supplier.

    AssumptionValueDetails and changes
    Waste allowance 10%
    Default An example allowance for cuts and breakage, added once. Change it for your own job.
    Sheet size No default
    Default An example set of sheet sizes, not a maker's range. Choose the size your supplier sells from the list above the result.
    Jointing compound per hundred square metres of board 40 L
    Default An example rate, not a maker's figure. It is a field above the result: replace it with the rate on your own label.
    Joint tape per hundred square metres of board 120 m (393 ft 8 7/16 in, converted)
    Default An example rate, not a maker's figure. It is a field above the result: replace it with the rate on your own label.
    Board area per screw 0.08 m² (0.86 ft², converted)
    Default An example rate, not a maker's figure. It is a field above the result: replace it with the rate on your own label.
    Tub size No default
    Default Choose it from the list above the result. Check your label or supplier.
    Tape roll length No default
    Default Choose it from the list above the result. Check your label or supplier.