Stair Carpet Calculator
HoneyDoMath.eu
Enter a flight's total rise and going, or type the number of stairs, to get the length of carpet for the treads and risers and the roll to buy in whole metres.
A ready-made setup of the Carpet Calculator.
Estimates for planning, not professional advice. Read the full notice.
Example: a straight flight
7 m of carpet
- Risers 15 risers
- Treads 14 treads
- Riser height 0.18 m (7.087 in)
- Length covered 6.2 m (20 ft 4 1/8 in)
- Roll length with the waste 6.82 m (22 ft 4 1/2 in)
Estimate for planning, from what you entered and the product data shown. Check product labels and your supplier before you buy.
Result
Enter a size to see your total.
Each product is rounded up once for the whole project, so the total can be less than the items bought alone added together. A line counted from a cut layout (sheets, boards or tiles laid out piece by piece) is counted for each item and added.
- Carpet (linear metres) 7
Questions
How much carpet do I need for 13 stairs?
Choose From a number of stairs, pick 13 stairs and type the riser height and going. Each stair takes its going plus its riser height. The stair width, waste allowance and roll width are examples until you change them.
What is the length of carpet for one step?
The going plus the riser height, plus any nosing wrap you add. The calculator adds the treads and the risers separately, so a flight whose top is the floor above has one tread fewer than risers.
Worked example: a straight flight
Show the working
- Treads: the going times the treads 0.25 m (9.843 in) × 14 treads = 3.5 m (11 ft 5 13/16 in)
- Risers: the riser height times the risers 0.18 m (7.087 in) × 15 risers = 2.7 m (8 ft 10 5/16 in)
- Add the waste allowance, once 6.2 m (20 ft 4 1/8 in) × 1.1 = 6.82 m (22 ft 4 1/2 in)
- Round up once, to whole metres of roll 6.82 m (22 ft 4 1/2 in) = 7 m of carpet
Assumptions
The figures behind the example. Sourced figures link to their source below; a default is a starting value to check against your label or supplier.
| Assumption | Value | Details and changes |
|---|---|---|
| Waste allowance | 10% | |
| Default A typical allowance, added once to the length covered. Change it for your job. | ||
| Stair width | No default | |
| Default The width of the carpet on the stair. Check your label or supplier. | ||
| Roll width | No default | |
| Default Your roll's width, from your supplier; the figure shown is an example to start from. Check your label or supplier. | ||
| Maximum riser height | No default | |
| Default Your own target; the figure shown is an example, not a rule. Check your label or supplier. | ||
Metres, centimetres or millimetres, like 3.8 m, 10 cm or 250 mm
What one step takes
The working for the example flight: a tread, a riser, one step and the whole flight
| Part | Length |
|---|---|
| Going | 0.25 m (9.843 in) |
| Riser height | 0.18 m (7.087 in) |
| One step | 0.43 m (16.929 in) |
| Treads and risers together | 6.2 m (20 ft 4 1/8 in) |
| With the waste allowance | 6.82 m (22 ft 4 1/2 in) |
One step is its going plus its riser height, with any nosing wrap you add. The flight is its treads and risers added, then the waste allowance once.