Carpet Calculator

Enter a room's length and width and your roll width to get the drops, seams and linear metres of carpet, with the drops run both ways and the shorter kept, rounded up once to whole metres. A drawn shape is counted as its bounding rectangle.

Estimates for planning, not professional advice. Read the full notice.

Room and roll

Metres, centimetres or millimetres, like 3.8 m, 10 cm or 250 mm

reads as 5.2 metres, 17 feet 3 quarters of an inch

Metres, centimetres or millimetres, like 3.8 m, 10 cm or 250 mm

reads as 4.5 metres, 14 feet 9 and 3 sixteenths inches

Metres, centimetres or millimetres, like 3.8 m, 10 cm or 250 mm

reads as 4 metres, 13 feet 1 and 1 half inches

Metres, centimetres or millimetres, like 3.8 m, 10 cm or 250 mm

Example: a living room

9 m of carpet

  • Carpet bought 36 m² (387.5 ft²)
  • Drops 2 drops
  • Seams 1 seam
  • The other way: linear metres 11 m (36 ft 1 1/16 in)
  • Carpet (linear metres) 9

Share this project

This link carries:

    The project is inside the link, after the # sign. Browsers do not send that part to the site.

    Questions

    Why not multiply the area by a waste factor?

    Carpet comes in a fixed roll width, and the room is covered by whole drops with seams between them. A room a little wider than the roll needs a whole extra drop for the strip left over, so the roll length decides the buy, not the area.

    Which roll width do I use?

    Enter the width of the roll your supplier cuts from. The calculator makes no claim about which widths are sold.

    What if I draw an L-shaped room?

    A drawn shape is counted as its bounding rectangle, the smallest rectangle that holds it, so the count can be more than the shape needs. Type each part as its own room for a closer count.

    Worked example: a living room

    Show the working
    1. Full drops across, and the fill strip left 5.2 m (17 ft 3/4 in) ÷ 4 m (13 ft 1 1/2 in) = 1 full drop
    2. Add the fill strip as one more drop 1 drop + 1 fill strip = 2 drops
    3. Linear metres: drops times the length of a drop 2 drops × 4.5 m (14 ft 9 3/16 in) = 9 m (29 ft 6 5/16 in)
    4. Round up once, to your supplier's whole metres 9 m (29 ft 6 5/16 in) = 9 m of carpet

    Assumptions

    The figures behind the example. Sourced figures link to their source below; a default is a starting value to check against your label or supplier.

    AssumptionValueDetails and changes
    Roll width No default
    Default Your roll's width, from your supplier; the figure shown is an example to start from. Check your label or supplier.
    Trim on each drop 0 mm (0 in, converted)
    Default Extra length on every drop, your own allowance. Check your label or supplier.

    The drops run both ways

    Drops, fill strip, linear metres and seams for the example room with the drops run along each side

    Drops, fill strip, linear metres and seams for the example room with the drops run along each side
    LayoutDropsFill strip widthLinear metresSeams
    Drops along the longer side 2500 mm (1 ft 7 11/16 in)11 m (36 ft 1 1/16 in)1
    Drops along the shorter side 21.2 m (3 ft 11 1/4 in)9 m (29 ft 6 5/16 in)1

    The calculator keeps the way that needs fewer linear metres, and fewer seams in a tie. Pile runs the same way on every drop and no pattern is matched.